wonderswan 燒錄bootrom

三级用户 s33050152 11月前 1503

有哪位大神懂如何烧bootrom

想改开机动画

无意间看到国外的教程

在wsceepdump的教学页面有教学文章跟档案

想看看有没有大佬玩过先请教下....


Installation Guide (Cartridge):

  1. Flash bootfriend-inst.wsc to the cartridge.
    • If your cartridge of choice uses a multiple choice menu, it is advisable to flash the installation program in place of said menu.
  2. Launch the cartridge. Examine the information on the status bar (top row).
    • If the status bar says EEP locked, BootFriend cannot be installed. Make sure you've flashed the installer correctly.
    • The Test BootFriend option allows you to test the program serial port loader without installing the splash screen. This is useful for ensuring that your serial port adapter will work with the firmware.
      • This does not display the configured custom splash! This is only for testing the serial port loader.
    • The Disable/Enable custom splash option allows you to disable a custom splash (to fix console freezes/hangs related to them) or enable one.
      • Note that, on SwanCrystal, there is a factory-installed custom splash screen on the IEEPROM, which is slightly different from the built-in one. The built-in splash screen is identical to the WonderSwan Color.
      • If BootFriend is installed, the option is named Disable/Enable BootFriend instead - as BootFriend is a modified custom splash, disabling the custom splash also disables BootFriend's functionality.
    • The SwanCrystal TFT recovery option allows you to fix missing TFT configuration data, as explained above.
  3. Select Install BootFriend and follow the instructions.
    • The right-hand side of the status bar should now say BF v.?? - this indicates a BootFriend installation.
  4. Once done, turn off the console. You can hold Y3 on boot to check for a successful BootFriend installation.
    • Note that the bootfriend-inst.wsc cartridge disables custom splashes on boot! You'll need to flash different data, or use a different cartridge, to verify BootFriend's operation.
    • The WonderSwan Color and SwanCrystal will not turn on if no valid cartridge is present. This is a normal feature of the console.

Installation Guide (WonderWitch .fx program):

(This method is experimental. If you run into problems, please use the "OS Upgrade" method.)

  1. Transfer bootfriend-inst.fx to WonderWitch.
  2. Follow instruction steps 2-4 from the "Cartridge" installation guide.
    • Using the WonderWitch method, the original IEEPROM contents are not saved to SRAM! Please use the XMODEM backup method instead.
    • Using the WonderWitch method, it is not always possible to "unbrick" a WonderSwan with damaged IEEPROM contents. This is a limitation of the method and cannot be fixed. (Note that the "SwanCrystal TFT recovery" function should work correctly.)

Installation Guide (WonderWitch OS Upgrade):

  1. The WonderWitch installer is currently only provided as an "OS Upgrade". Therefore, the installation process is a little different from a typical WonderWitch program:
    • Start WonderWitch in Freya Monitor mode - hold B while the console is turning on.
    • Configure the serial baud rate in the Setup menu.
    • Select Send System and download a backup of the currently installed OS.
      • For downloading and uploading the OS, one can use an XMODEM transfer tool (as described in "Usage"), or TransMagic's built-in FreyaOS update functionality.
      • If you forget to do this, you can find a copy of FreyaOS 1.2.0 on Qute's website (=> ダウンロード).
    • Select Recv System and upload the bootfriend-inst-wwsystem.bin file.
  2. Follow instruction steps 2-4 from the "Cartridge" installation guide.
    • Using the WonderWitch method, the original IEEPROM contents are not saved to SRAM! Please use the XMODEM backup method instead.
    • Using the WonderWitch method, it is not always possible to "unbrick" a WonderSwan with damaged IEEPROM contents. This is a limitation of the method and cannot be fixed. (Note that the "SwanCrystal TFT recovery" function should work correctly.)
  3. Launch Freya Monitor again, and use Recv System with a copy of FreyaOS to restore the original operating system.



我現在卡在第二關....

不知道怎樣把專用的boot 改寫入

eeprom要用專用的燒錄器寫入 這個朋友要幫我用

求達人指點



上一篇:两晚历时五个多小时把NGC手柄改成了无线方式
下一篇:求助WIIU的教程
最新回复 (8)
  • 六级用户 进站劣人 11月前
    0 2
    都没摸过WS实机,羡慕了。
  • 三级用户 s33050152 11月前
    0 3
    进站劣人 都没摸过WS实机,羡慕了。

    其實機器國外不貴....


  • 六级用户 进站劣人 11月前
    0 4
    s33050152 其實機器國外不貴....
    游戏卡不便宜吧,上面的几作机战我全都用PSP模拟器玩了。
  • 三级用户 s33050152 11月前
    0 5
    进站劣人 游戏卡不便宜吧,上面的几作机战我全都用PSP模拟器玩了。
    燒錄卡大概900 rmb 機器如果改高清 450rmb
  • 六级用户 进站劣人 11月前
    0 6
    s33050152 燒錄卡大概900 rmb 機器如果改高清 450rmb
    900!!!
    告辞。
  • 三级用户 s33050152 11月前
    0 7
    进站劣人 900!!! 告辞。
    - -官方牌價就110us了國際運費跟關稅算一算大概抓900....
  • 三级用户 s33050152 11月前
    0 8
    更新文章了
  • 三级用户 Pyrrhus 11月前
    0 9
    WS最有价值的是那些纵版射击游戏,其他机器上很难玩出那个效果
    • 老男人游戏网配套论坛
      10
        立即登录 立即注册
发新帖
本论坛禁止发布SWITCH和PS4相关资源,若有其他侵权内容,请致邮3360342659#qq.com(#替换成@)删除。